EXACTLY HOW TO INSTALL A BATH TUB: SET UP AN ACRYLIC TUB AND ALSO BATHTUB SURROUND

Exactly How to Install a Bath Tub: Set Up an Acrylic Tub and Also Bathtub Surround

Exactly How to Install a Bath Tub: Set Up an Acrylic Tub and Also Bathtub Surround

Blog Article

Website

Presented here down the page you can discover additional very good information and facts in regards to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.


A Step-by-Step Guide to Installing a Bathtub
Setting up a bath tub isn't precisely brain surgery, but it does need strong plumbing, carpentry, and also sometimes, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably hard job. If the old bathtub is readily available, the task can move immediately; if you need to open a wall surface to get rid of the old bathtub and position the new tub, the job is a lot harder. In either case, the project is within a house handyman's abilities, although you will certainly require a helper to move out the old tub as well as set in the brand-new one. See to it you have qualified yourself for the task as well as are comfortable attempting it. Rather than employing a specialist to take control of a halfway-completed task, it is far better to consider using one before you begin. Chances are you may need an expert plumber to make tube connections.
This write-up will assist you set up a brand-new bath tub in your washroom if you have actually currently acquired a brand-new bathtub and also do not require to transform the arrangement of your previous supply of water pipes.
Your tools and material checklist should comprise the following:
  • New Bathtub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipeline Caps


  • Removing Old Taps


    If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you must do is detach the water system. After doing so, switch on the taps to drain any water continuing to be in the system. The procedure of eliminating the existing faucets can be rather problematic due to the limited accessibility that is commonly the situation.
    Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the faucets. Have a towel prepared for the remaining water that will originate from the pipes. Once the supply pipes have actually been eliminated, use the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any old sealing compound.
    Before moving on to fit the brand-new faucets, contrast the pipeline connections on the old taps to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new faucets to fit.

    Suitable New Touches


    If the tails of the new taps are plastic, then you will certainly require a plastic port to avoid damage to the thread. One end of the port fits on the plastic tail of the tap and the various other end gives a link to the existing supply pipes.
    If you need to fit a monobloc, after that you will certainly need decreasing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
    Next off, position the tap in the placing opening in the bath/basin making sure that the washers remain in location between the tap and also the sink. Secure the faucet in position with the producer provided backnut. As soon as the faucet is securely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular tap connectors. The previous type should be attached to the tap ends initially, tightening only by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been attached.

    Setting up the Bathtub


    Making use of both wooden boards under its feet, position the bathtub in the called for setting. The wooden boards are practical in uniformly spreading out the weight of the tub over the area of the boards as opposed to focusing all the weight onto 4 little factors.
    The next objective is to make sure that the bathtub is leveled all round. This can be attained by checking the level and readjusting the feet on the bathtub till the spirit level reviews level.
    To mount taps, fit all-time low of the furthest adaptable tap port to the appropriate supply pipeline by making a compression join; after that do the very same for the other tap.
    Activate the supply of water and also check all joints and also new pipework for leakages and also tighten them if required. Load the bathtub as well as additionally inspect the overflow outlet and also the normal outlet for leaks.
    Ultimately, deal with the bath paneling as explained in the maker's user's manual. Tiling and sealing around the tub needs to wait until the bathtub has actually been used a minimum of when as this will certainly resolve it into its final setting.

    Getting ready for the Setup


    To start with, the sustaining structure supplied with the bath ought to be fitted (if needed) according to the maker's guidelines. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is necessary to see to it that if the faucet comes with a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets system to stop pressure on the bath tub.
    Fit the adaptable faucet adapters to the bottom of both faucets making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you use all of the provided washing machines.
    Attach the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath should currently prepare to be fitted in its last setting.

    Tiling Around the Tub


    In the area where the bath fulfills the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the installation can relocate enough to crack an inflexible seal, creating the water to permeate the wall in between the bathroom as well as the tiling, leading to complications with wetness as well as possible leakages to the ceiling listed below.
    You can choose from a variety of coloured sealers to blend in your fixtures and also fittings. They are sold in tubes and also cartridges, as well as are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to always fill the bath tub with water before securing, to enable the movement experienced when the bathtub is in usage. The sealant can crack rather early if you do not think about this motion before securing.
    Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise conveniently offered on the market. It is a good idea to fit the tiles making use of waterproof or water resistant glue and cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    Tools You Need to Install a New Bathtub

    We were made aware of that report on How to Install a Bathtub through someone on our other web page. Do you know somebody who is looking into the subject? Take a moment to share it. I am grateful for your time. Come back soon.




    Go Deal


    Report this page